ry (for AMI/AWARD or other BIOSes)
LKWPETER, lkwpeter, BIOSTAR, biostar, BIOSSTAR, biosstar, ALFAROME, Syxz, Wodj,phonix,toshiba
remember that passwords are Case Sensitive.
hacking BIOS via software
If you have access to the computer when it’s turned on, you could try one of those
programs that remove the password from the BIOS, by invalidating its memory.
However, it might happen you don’t have one of those programs when you have access
to the computer, so you’d better learn how to do manually what they do. You can reset
the BIOS to its default values using the MS-DOS tool DEBUG (type DEBUG at the
command prompt. You’d better do it in pure MS-DOS mode, not from a MS-DOS shell
window in Windows). Once you are in the debug environment enter the following
commands:
AMI/AWARD BIOS
O 70 17
O 71 17
Q
PHOENIX BIOS
O 70 FF
O 71 17
Q
GENERIC
Invalidates CMOS RAM.
Should work on all AT motherboards
(XT motherboards don’t have CMOS)
O 70 2E
O 71 FF
Q
Note that the first letter is a “O” not the number “0″. The numbers which follow are two
bytes in hex format.
Hacking BIOS via hardware
If you can’t access the computer when it’s on, and the standard backdoor passwords
didn’t work, you’ll have to flash the BIOS via hardware. Please read the important notes
at the end of this section before to try any of these methods.
Using the jumpers
The canonical way to flash the BIOS via hardware is to plug, unplug, or switch a jumper
on the motherboard (for “switching a jumper” I mean that you find a jumper that joins
the central pin and a side pin of a group of three pins, you should then unplug the
jumper and then plug it to the central pin and to the pin on the opposite side, so if the
jumper is normally on position 1-2, you have to put it on position 2-3, or viceversa).
This jumper is not always located near to the BIOS, but could be anywhere on the
motherboard.
To find the correct jumper you should read the motherboard’s manual.Once you’ve located the correct jumper, switch it (or plug or unplug it, depending from
what the manual says) while the computer is turned OFF. Wait a couple of seconds then
put the jumper back to its original position. In some motherboards it may happen that
the computer will automatically turn itself on, after flashing the BIOS. In this case, turn
it off, and put the jumper back to its original position, then turn it on again. Other
motherboards require you turn the computer on for a few seconds to flash the BIOS.
If you don’t have the motherboard’s manual, you’ll have to “bruteforce” it… trying out all
the jumpers. In this case, try first the isolated ones (not in a group), the ones near to the
BIOS, and the ones you can switch (as I explained before). If all them fail, try all the
others. However, you must modify the status of only one jumper per attempt, otherwise
you could damage the motherboard (since you don’t know what the jumper you
modified is actually meant for). If the password request screen still appear, try another
one.
If after flashing the BIOS, the computer won’t boot when you turn it on, turn it off, and
wait some seconds before to retry.
Removing the battery
If you can’t find the jumper to flash the BIOS or if such jumper doesn’t exist, you can
remove the battery that keeps the BIOS memory alive. It’s a button-size battery
somewhere on the motherboard (on elder computers the battery could be a small,
typically blue, cylinder soldered to the motherboard, but usually has a jumper on its side
to disconnect it, otherwise you’ll have to unsolder it and then solder it back). Take it
away for 15-30 minutes or more, then put it back and the data contained into the BIOS
memory should be volatilized. I’d suggest you to remove it for about one hour to be
sure, because if you put it back when the data aren’t erased yet you’ll have to wait more
time, as you’ve never removed it. If at first it doesn’t work, try to remove the battery
overnight.
Important note: in laptop and notebooks you don’t have to remove the computer’s power
batteries (which would be useless), but you should open your computer and remove the
CMOS battery from the motherboard.
Short-circuiting the chip
Another way to clear the CMOS RAM is to reset it by short circuiting two pins of the
BIOS chip for a few seconds. You can do that with a small piece of electric wire or with
a bended paper clip. Always make sure that the computer is turned OFF before to try
this operation.
Here is a list of EPROM chips that are commonly used in the BIOS industry. You may
find similar chips with different names if they are compatible chips made by another
brand. If you find the BIOS chip you are working on matches with one of the following
you can try to short-cicuit the appropriate pins. Be careful, because this operation may
damage the chip.
Important
Whether is the method you use, when you flash the BIOS not only the password, but
also all the other configuration data will be reset to the factory defaults, so when you are
booting for the first time after a BIOS flash, you should enter the CMOS configuration
menu (as explained before) and fix up some things.
Also, when you boot Windows, it may happen that it finds some new device, because of
the new configuration of the BIOS, in this case you’ll probably need the Windows
installation CD because Windows may ask you for some external files. If Windows
doesn’t see the CD-ROM try to eject and re-insert the CD-ROM again. If Windows can’t
find the CD-ROM drive and you set it properly from the BIOS config, just reboot with
the reset key, and in the next run Windows should find it. However most files needed by
the system while installing new hardware could also be found in C:\WINDOWS,
C:\WINDOWS\SYSTEM, or C:\WINDOWS\INF .
change C with your windows drive letter if it is not in C drive
LKWPETER, lkwpeter, BIOSTAR, biostar, BIOSSTAR, biosstar, ALFAROME, Syxz, Wodj,phonix,toshiba
remember that passwords are Case Sensitive.
hacking BIOS via software
If you have access to the computer when it’s turned on, you could try one of those
programs that remove the password from the BIOS, by invalidating its memory.
However, it might happen you don’t have one of those programs when you have access
to the computer, so you’d better learn how to do manually what they do. You can reset
the BIOS to its default values using the MS-DOS tool DEBUG (type DEBUG at the
command prompt. You’d better do it in pure MS-DOS mode, not from a MS-DOS shell
window in Windows). Once you are in the debug environment enter the following
commands:
AMI/AWARD BIOS
O 70 17
O 71 17
Q
PHOENIX BIOS
O 70 FF
O 71 17
Q
GENERIC
Invalidates CMOS RAM.
Should work on all AT motherboards
(XT motherboards don’t have CMOS)
O 70 2E
O 71 FF
Q
Note that the first letter is a “O” not the number “0″. The numbers which follow are two
bytes in hex format.
Hacking BIOS via hardware
If you can’t access the computer when it’s on, and the standard backdoor passwords
didn’t work, you’ll have to flash the BIOS via hardware. Please read the important notes
at the end of this section before to try any of these methods.
Using the jumpers
The canonical way to flash the BIOS via hardware is to plug, unplug, or switch a jumper
on the motherboard (for “switching a jumper” I mean that you find a jumper that joins
the central pin and a side pin of a group of three pins, you should then unplug the
jumper and then plug it to the central pin and to the pin on the opposite side, so if the
jumper is normally on position 1-2, you have to put it on position 2-3, or viceversa).
This jumper is not always located near to the BIOS, but could be anywhere on the
motherboard.
To find the correct jumper you should read the motherboard’s manual.Once you’ve located the correct jumper, switch it (or plug or unplug it, depending from
what the manual says) while the computer is turned OFF. Wait a couple of seconds then
put the jumper back to its original position. In some motherboards it may happen that
the computer will automatically turn itself on, after flashing the BIOS. In this case, turn
it off, and put the jumper back to its original position, then turn it on again. Other
motherboards require you turn the computer on for a few seconds to flash the BIOS.
If you don’t have the motherboard’s manual, you’ll have to “bruteforce” it… trying out all
the jumpers. In this case, try first the isolated ones (not in a group), the ones near to the
BIOS, and the ones you can switch (as I explained before). If all them fail, try all the
others. However, you must modify the status of only one jumper per attempt, otherwise
you could damage the motherboard (since you don’t know what the jumper you
modified is actually meant for). If the password request screen still appear, try another
one.
If after flashing the BIOS, the computer won’t boot when you turn it on, turn it off, and
wait some seconds before to retry.
Removing the battery
If you can’t find the jumper to flash the BIOS or if such jumper doesn’t exist, you can
remove the battery that keeps the BIOS memory alive. It’s a button-size battery
somewhere on the motherboard (on elder computers the battery could be a small,
typically blue, cylinder soldered to the motherboard, but usually has a jumper on its side
to disconnect it, otherwise you’ll have to unsolder it and then solder it back). Take it
away for 15-30 minutes or more, then put it back and the data contained into the BIOS
memory should be volatilized. I’d suggest you to remove it for about one hour to be
sure, because if you put it back when the data aren’t erased yet you’ll have to wait more
time, as you’ve never removed it. If at first it doesn’t work, try to remove the battery
overnight.
Important note: in laptop and notebooks you don’t have to remove the computer’s power
batteries (which would be useless), but you should open your computer and remove the
CMOS battery from the motherboard.
Short-circuiting the chip
Another way to clear the CMOS RAM is to reset it by short circuiting two pins of the
BIOS chip for a few seconds. You can do that with a small piece of electric wire or with
a bended paper clip. Always make sure that the computer is turned OFF before to try
this operation.
Here is a list of EPROM chips that are commonly used in the BIOS industry. You may
find similar chips with different names if they are compatible chips made by another
brand. If you find the BIOS chip you are working on matches with one of the following
you can try to short-cicuit the appropriate pins. Be careful, because this operation may
damage the chip.
Important
Whether is the method you use, when you flash the BIOS not only the password, but
also all the other configuration data will be reset to the factory defaults, so when you are
booting for the first time after a BIOS flash, you should enter the CMOS configuration
menu (as explained before) and fix up some things.
Also, when you boot Windows, it may happen that it finds some new device, because of
the new configuration of the BIOS, in this case you’ll probably need the Windows
installation CD because Windows may ask you for some external files. If Windows
doesn’t see the CD-ROM try to eject and re-insert the CD-ROM again. If Windows can’t
find the CD-ROM drive and you set it properly from the BIOS config, just reboot with
the reset key, and in the next run Windows should find it. However most files needed by
the system while installing new hardware could also be found in C:\WINDOWS,
C:\WINDOWS\SYSTEM, or C:\WINDOWS\INF .
change C with your windows drive letter if it is not in C drive
